ELECTRONIC EQUIPMENT

FOR THE

ELEVATOR INDUSTRY

Shortform

CONTROLES S.A.

CONTROLES S.A.

Electrónica Industrial y Telecomunicaciones

Avenida Rivera 3314

11300 Montevideo

Uruguay

Tel.: +598 (2) 622 0651

Fax: +598 (2) 622 2048

E-mail: info@controles.com

www.controles.com

Otherwise, the controllers may be used in industrial control applications. In this case the base program in the ROM creates a multitask system, 10 independent tasks, real time clock. This system is user programmable (usually C) through a series port.

The controllers and accessories listed below offer a complete solution for the logic command, group supervision and car and hall signaling, from simple one car to six car, 40 landing, remotely supervised system, including software tools for testing and controller configuration.

CONTROLLERS

Simple automatic, 4 landing, 1 or 2 velocity AC motor, VV, VVVF, hydraulic systems.

Many possible configurations, typically 8 landing collective down selective, 1 or 2 velocity AC motor, VV, VVVF, hydraulic systems.

Without expansion board: many possible configurations, typically 24 landing collective down selective or 16 landing collective full selective, isolated controller, master controller, slave controlled.

With expansion board: many possible configurations, up to 40 landing collective full selective, isolated controller, master controller, slave controlled.

Applicable to 1 or 2 velocity AC motor, VV, VVVF, hydraulic systems, DC motors (Ward Leonard or Static Drive).

This board may be implemented up to

• 48 input/output pin
• RS232-c serial port
• RS422 serial line
• 8 relay

To optimize a system up to 6 car, 40 landing, collective full selective.

CEA51FA partially implemented, with or without expansion, to be used as hall call controller in a group.

Handheld terminal to read the configuration, to change some of the parameters, to read event logging, to document inspection date and others.

Two or three 7*5 LED matrix, dynamic position indicator with or without gong generator. A series RS232-c line from the TTL controller port and auxiliary drive commands the indicator.

Audio message generator, standard, custom or user generated messages.

Two seven segment display with "three wire" command: common, power supply and a command line directly from an output pin at the controller.

One or two 7 or 14 (16) segment display, directly commanded by the controller.

1 to 3 tone drive signal, for 8 ohm loudspeaker.

To be mounted into an insulated case. Custom design.

The board receives commands from a 12 keys keyboard to enable or to inhibit the operation of a push button.

SP51 active at 24 Vdc, SP31 active at 0 Vdc and SP3151 with both outputs.

Encapsulated and protected reed switch.

To be driven from an open collector controller output.

To be driven from an 8 pin open collector controller output strip.

To be driven from the 8 pin auxiliary CMOS level controller output strip.

The board has 4 address and 1 enable input, to be driven from the 8 pin auxiliary CMOS level controller output strip. It is useful for the command of linear (lamp) position indicators, landing lanterns, leveled car lights.

Transforms 8 pin auxiliary CMOS level controller outputs to 8 open collector outputs, 24 Vdc, 50 mA

Transforms 8 open collector controller outputs to 8 NPN open collector outputs, 24 Vdc, 2 A or 110 Vdc, 100 mA.

Transforms 8 open collector controller outputs to 8 open collector outputs, PNP 24 Vdc, 50 mA.

To eliminate registered call LED flickering in some special situations.

Optically isolates and transforms 8 open collector controller outputs to 8 NPN open collector outputs, 24 Vdc, 1 A.

For call button signal, with or without isolation, from several voltage levels to 24 Vdc.

From several voltage levels to 24 Vdc, with optical isolation. Includes a two 7 segment display position indicator, a 24 Vdc 200 mA power supply and the multiplexing command for CEA31.

For 1.51 Position Sensor System, for car velocities from 90m/m on.

This is an interface between AC power line voltages and SF1, SF2 and SF3 input pins in the CEA51FA controller, to be used for line supervision.

For 1.51 and 8.51 Position Sensor System, for car velocities up to 160m/m. Includes an interface between AC power line voltages and SF1, SF2 and SF3 input pins in the CEA51FA controller, to be used for line supervision.

TTL to RS232-c level. Interfaces TTL controller port to PC, IML2D50L dynamic position indicator, AV51FA voice annunciator.

TTL to RS422 level. Interfaces 422 expansion board port to line to PC.

RS232-c to RS422 level. Interfaces 422 line to PC, 232 controller port to 422 line, etc.

Cable and adapter kit to interface TTL controller port to accessories.

Interfaces RS232-c and RS422 in short distance applications.

Economical interface between TTL controller port and accessories in short distance applications.

COO51FA to T51FA cable.

CEAxx controller to T51FA cable.

TTL controller port to IML2D50L driver.

Auxiliary relay, mounts to DIN rail.

For system communications: CEA51FA master to slave, COO51FA to CEA51FA controllers.

To use for door or gate access supervision, to 7 m width.

To use for door access supervision, to 0,9m width.

Board with 10 3AG fuseholders and terminal strips.

This board includes five simple RC arc suppressor circuit and one RCRD for retracting cam or similar loads application.

Standard E23 or E31, for controllers and accessories: electronic push button, indicator, etc.

28 mm leg, with or without mounted power supply board for electronics (24 Vdc 1 A) and power circuits (110 Vdc 4 A, isolated 220 Vac 0.5 A, 10 Vac 5)

3 to 8 pin, to facilitate equipment substitution.

All standard parts in controllers and accessories.

Standard programmable parts with the specific application program loaded.

PC software, to configure CEA51FA, CEA31, CEA10 or COO51FA.

PC software, to assemble messages for the AV51FA voice annunciator.

PC software, for local or remote system supervision.

Custom configured elevator controller ROM.

To test all controller CPU parts, input and output functions.

Application software for CEA31 controller, to simulate hoistway with several kinds of doors and position sensors, to test elevator controller command logic and COO51FA group controller logic.

Application software for CEA31 PLC, to implement an access controller for up to 22 push button car panel.